#

Standards and directives

We operate in a regulated global market in many countries. Thus, we must manage requirements that may vary greatly between countries or regions.
The common goal of our product managers and services is to offer reliable, sustainable, high-performance products in compliance with the regulations and/or standards of each territory where they are used.
#
#

Standards and certifications

All you need to know about PPE standards

Reset all
Filter
Standards

EN361 FULL BODY HARNESS

Body securing device intended to stop falls. The full body harness can be made of straps, buckles and other elements; set and adjusted in a right way on the body of an individual to secure him during a fall and afterwards.

ANSI Z359.3-2019

Safety Requirements for Lanyards and Positioning Lanyards

ANSI Z359.11-2021

Safety Requirements for Full Body Harnesses

EN358 BELTS AND POSITIONING LINES

A work positioning system consists of elements (belt and work positioning line), joined together to form a complete piece of equipment.

EN388 : ISO 23 388 MECHANICAL RISKS

The EN388 standard applies to all types of protective gloves with respect to physical and mechanical aggression from abrasion, cutting from slicing, perforation and tearing. Since the 2016 version of the standard, new optional performance have appeared.

 

TEST Level 1 Level 2 Level 3 Level 4 Level 5
Abrasion resistance
(Number of cycles)		 100 500 2,000 8,000 -
Blade cutting resistance (index) 1.2 2.5 5 10 20
Tear resistance (N) 10 25 50 75 -
Puncture resistance (N) 20 60 100 150 -

 

Impact resistance on the metacarpal area: if this performance is claimed, the "P" mark appears.

Marking example:

4233X P

 

TEST CUT RESISTANCE
EN ISO 13997 (TDM		 LEVEL A LEVEL B LEVEL C LEVEL D LEVEL E   LEVEL F
APPLIED FORCE (N) 2 5 10 15 22 30

 

Marking example:


4543D ou 4X43D

Cut by blade, 2 test methods:

EN388 6.2.:  For low to middle risk of cutting. A circular blade on which a constant force of 5 N is applied, moves back and forth until the sample is cut. It measures the number of completed cycles and is credited with the corresponding level.

EN ISO 13997:  For materials that blunt the blade during the EN388 6.2 test and/ or are particularly resistant, for high risk of cutting. A straight blade makes a single movement of 20 mm with a force of 2N, the test is repeated with a different force as many times as necessary until the sample is cut. A level corresponding to the force required to cut the sample is assigned. This method better represents the usage situations that present a high risk of cutting.

ANSI/ISEA Z89.1: American standard for head protection in industry

MANDATORY

Type 1: The impact force transmitted to the cap must not exceed 4,450 N when a 3.6 kg (8 lb) impact is dropped at a speed of 5.5 m/s (metres per second).
Penetration: A 1 kg penetrator must not come into contact with the false head at a speed of 7.0 m/s.
Flammability: the helmet must not burn with the emission of a fl ame for more than 5 seconds after the fl ame has been withdrawn
Electrical resistance: proof test at 20,000 volts for class E or 10,000 volts for class G. Class C off ers no protection against electrical hazards.
Type 2: In addition to the requirements of type 1, type 2 head protection must also satisfy:
Energy attenuation: the acceleration must not exceed 150 g in the event of a fall onto the cap and sideways using a 5 kg dummy head at 3.5 m/s.
Lateral penetration: At the front, rear and sides, a 1 kg penetrator must not come into contact with the headform at a speed of 5.0 m/s.

OPTIONAL

ANSI/ISEA Z89.1 4 options: low temperature (LT), high temperature (HT), reverse wear position and high visibility.